Just how do you actually feel on the subject of Installing A Bathtub?
Setting up a bath tub isn't specifically rocket science, however it does need solid plumbing, woodworking, and in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a moderately challenging project. If the old tub is conveniently obtainable, the project can move rapidly; if you have to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly need an assistant to vacate the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the job as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may need a professional plumber to make tube links.
This post will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently bought a brand-new bathtub and also do not require to transform the setup of your previous water system pipes.
Your devices and also product list need to make up the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome because of the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will come from the pipelines. When the supply pipes have actually been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Prior to carrying on to fit the new faucets, compare the pipe connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Secure the faucet in position with the producer given backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be attached to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Making use of the two wood boards under its feet, position the tub in the called for position. The wooden boards are practical in evenly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the level and changing the feet on the tub till the level reads level.
To set up faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; after that do the same for the other tap.
Activate the water supply and inspect all joints as well as brand-new pipework for leakages as well as tighten them if required. Fill up the tub as well as additionally check the overflow outlet and the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as securing around the tub needs to wait till the bath tub has actually been made use of at the very least when as this will settle it into its last position.
Preparing for the Installation
First of all, the supporting frame supplied with the bath should be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in difficulties with moisture and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the bath tub with water before securing, to allow for the motion experienced when the tub remains in use. The sealer can break rather early if you do not take into account this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that article on Installing A Bathtub while exploring the search engines. For those who liked our page kindly make sure you remember to pass it around. We value reading our article about How to Install a Bathtub Yourself.
Quote & Schedule